TED Revisionen

    • Offizieller Beitrag

    Hallo!


    Hab mal eine Frage. Ein TED 8365 in südamerikanischer Ausführung PAL-N, macht der nur "Blödsinn" wenn ich einen "europäischen" PAL-TV an den TV-Modulator anschließe, oder auch wenn ich einen 1084 oder ähnlichen 15 kHz Monitor an die Videobuchse anschließe?


    Sprich, wenn mir TV Ausgabe egal ist, kann ich so einen TED dann als Reparaturlösung verwenden?


    siehe : http://plus4world.powweb.com/hardware/MOS_8365


    Gruß
    Stephan

  • Gibt es denn Berichte, dass es Bildsalat gibt? Das dürfte sich nämlich nicht unterscheiden zwischen HF und CVBS Signal, wenn die Unterschiede nur bei Farbträger und Tonträger Frequenz sind.


    Ich meine aber auch einmal gelesen zu haben, dass etwas an einem Sync Signal geändert wurde. Das wäre dann das totale Aus.


    Oder mal jemand fragen der einen Drean C16 hat.


    Gruß x1541

    Zuletzt repariert:

    10.11. defektes µT RAM im Apple //e ersetzt

    10.11. defektes µT RAM im Atari 130XE ersetzt

    12.11. VC20 mit black screen: defekter Videotransistor ersetzt

    • Offizieller Beitrag

    Zitat von plus4world:


    PAL-N is basically normal PAL, with a different (lower) color subcarrier frequency.
    -- In the Drean C-16, you can find a 8365 TED instead of the usual 8360.
    -- The oscillator runs off a crystal of 14.32822MHz -- a bit faster than NTSC's 14.31818.
    -- The motherboard is otherwise a regular NTSC C-16 motherboard, with the usual European Kernal installed.


    Speaking
    of the 8365 -- my first impression is that it's a "regular" 8360, and
    they only modified one parameter, the constant which is used to divide
    the oscillator clock to obtain the processor and the dot clocks. To get
    the CPU single clock in the 8360, in PAL, one would divide the crystal
    freq by 20, and in NTSC mode, by 16. In the 8365, both dividers are the
    same, 16.


    As consequences:


    -- When switching between PAL
    and NTSC mode on the 8365, one would get visible picture on a PAL/NTSC
    capable TV, at least in black and white (unlike regular 8360-equipped
    machines, where either the PAL or the NTSC mode is displayable on
    regular tv's, but not both).


    -- The color subcarrier won't, but
    the color encoding should change according to the PAL/NTSC bit
    (subcarrier freq is the same). With an NTSC crystal, the 8365 should
    also be capable of providing standard NTSC signal.


    -- With the
    PAL-N crystal installed, colors are obviously only seen on PAL-N capable
    TVs or such PC tuner cards. The color palette for PAL-N mode should be
    similar to regular PAL colors, but the color resolution is worse, 2
    pixels vs. 1.6. (In other words, in this respect PAL-N is NTSC's color
    resolution with the PAL palette).


    The CPU (single) clock of the
    computer is the highest amongst all known TED based computers; it's
    about 0.895514Mhz. As a consequence: as it's a "regular" PAL machine
    with a slightly faster clock, all European C-16 software should work on
    the PAL-N C-16, but floppy fast-loaders may fail to work. European stuff
    messing with the PAL/NTSC bit should fail, too (but other tricky stuff,
    like sideborder-removing should work... I'll yet have to test those,
    but I don't expect anything irregular...).

  • Zur Not als NTSC Rechner verwenden. Das dürfte ja problemlos funktionieren.


    Gruß x1541

    Zuletzt repariert:

    10.11. defektes µT RAM im Apple //e ersetzt

    10.11. defektes µT RAM im Atari 130XE ersetzt

    12.11. VC20 mit black screen: defekter Videotransistor ersetzt

  • Hast du den passenden quartz eingebaut? Hast du mal ein NTSC ROM probiert?


    Gruß x1541

    Zuletzt repariert:

    10.11. defektes µT RAM im Apple //e ersetzt

    10.11. defektes µT RAM im Atari 130XE ersetzt

    12.11. VC20 mit black screen: defekter Videotransistor ersetzt

  • Die Info ist ja im link in deinem ersten Beitrag.


    The oscillator runs off a crystal of 14.32822MHz -- a bit faster than NTSC's 14.31818.


    Einfacher zu bekommen ist sicher der NTSC quarz. Denke der Monitor sollte damit trotzdem synchronisieren. Momentan ist deine Zeilen Frequenz zu hoch durch den 17.734MHz PAL-B Quarz.


    Das ROM schaltet ja doch nur das NTSC Bit um. Kannst probieren wenn der Quarz Wechsel nichts bringt.


    Gruß x1541

    Zuletzt repariert:

    10.11. defektes µT RAM im Apple //e ersetzt

    10.11. defektes µT RAM im Atari 130XE ersetzt

    12.11. VC20 mit black screen: defekter Videotransistor ersetzt