Hallo!
Weiß jemand, ob man damit:
http://www.ebay.com/itm/SCA80-…a71fac:g:x14AAOSw-0xYbRU0
SCSI Ultra wide Festplatten an Geräten mit 50poligem SCSI Kabel verwenden kann?
Danke
Stephan
Hallo!
Weiß jemand, ob man damit:
http://www.ebay.com/itm/SCA80-…a71fac:g:x14AAOSw-0xYbRU0
SCSI Ultra wide Festplatten an Geräten mit 50poligem SCSI Kabel verwenden kann?
Danke
Stephan
Die verlinkte Beschreibung bezieht sich auf dem umgekehten Fall, also narrow Platte an wide Bus.
Der Adpater für SCA-Platten am narrow Bus funktioniert erfahrungsgemäß Problemlos.
Host Adapter und Geräte handeln bei der Bus-Initialisierung die Übertragunsmodalitäten aus.
Es wird kein wide SCSI Protokoll ausgehandelt, wenn das nicht beide beteiligten können.
In hier angefragten Fall ist der Host Adapter nicht wide SCSI fähig.
Also werden die höheren Leitungen auch nicht benutzt.
Denkt dran, der beschriebene Adapter ist für Festplatten mit SCA Anschluss! Der Anschluss für "normale" Wide SCSI Platten sieht zwar ähnlich aus, ist aber nicht so breit. Der SCA-Anschluß ist für Festplatten im HotPlugin-Betrieb, da läuft auch die Stromzufur über den SCA Anschluss.
Die verlinkte Beschreibung bezieht sich auf dem umgekehten Fall, also narrow Platte an wide Bus.
Der Adpater für SCA-Platten am narrow Bus funktioniert erfahrungsgemäß Problemlos.
Host Adapter und Geräte handeln bei der Bus-Initialisierung die Übertragunsmodalitäten aus.
Es wird kein wide SCSI Protokoll ausgehandelt, wenn das nicht beide beteiligten können.
In hier angefragten Fall ist der Host Adapter nicht wide SCSI fähig.
Also werden die höheren Leitungen auch nicht benutzt.
Verlinkte Beschreibung war schon richtig. Zumindest mechanisch/elektrisch funktioniert es.
Eine Sun Sparcstation classic kann nichts damit anfangen Vielleicht Platte zu groß (18GB).
Hat jemand eine Idee, was die Jumper tun? Die Namen sind von oben nach unten:
"TPR", "DLY","REM","LED","SNC","SNC","ID0","ID1","ID2".
LED und ID0-2 sind mir klar, aber der Rest?
Hat jemand eine Idee, was die Jumper tun? Die Namen sind von oben nach unten:
"TPR", "DLY","REM","LED","SNC","SNC","ID0","ID1","ID2".
LED und ID0-2 sind mir klar, aber der Rest?
TPR - Termpower ; Strom liefern für die Terminatorleitung ; macht normalerweise schon der Controller, schadet aber auch nichts, wenns vom Laufwerk kommt
DLY - Delay ; Zeitverzug zwischen Plattenanlaufen und Abfrage
REM und SNC fällt mir grad nix zu ein - SNC vielleicht für "Sorry, not connected" ... andere Leute mit Ideen wissen da vielleicht mehr
Verlinkte Beschreibung war schon richtig.
Ich habe mich damals hauptsaechlich an dem Bild mit Narrow-Controller und Wide-Device orientiert. Das ist ok.
Der Text selber ist nicht 100% eindeutig.
Eine Sun Sparcstation classic kann nichts damit anfangen
Jedes SCSI Device hat eine Vendor-ID und Device-ID, die werden i.a. beim booten angezeigt.
Wenn du die siehst, ist auf jeden Fall das SCSI Device erreichbar und antwortet.
Viel Erfolg
REM steht für Remote Start und SNC für Synchronous.
REM steht für Remote Start und SNC für Synchronous.
Ist schon ein paar Tage her, aber was bedeutet "Synchronous" in diesem zusammenhang?
Bei synchroner Datenübertragung kommen mehr Bytes pro Sekunde über den Bus. Das müssen beide Geräte können, ansonsten wird der asynchronmodus benutzt.
Ich hab’s mal gegoogelt. Bei Async. wird nach jedem Request auf ein Ack gewartet. Bei Sync. können einige Requests geschickt werden, bevor die entsprechenden Ack. kommen. Passt mMn nicht so ganz von der Namensgebung, hatte aber einige gleiche Treffer.
Bei mir kommen ausschließlich LVD/SE SCA80 Platten mit Adapter auf 50pol zum Einsatz. Da die billigen(*) Anschluß-Adapter keine aktive Terminierung können bis auf TPR, die LVD Platten es zumeist nicht mehr bieten (JMP), ältere ja, bleibt für die Terminierung eigentlich nur ein Laufwerk mit integrierter Terminierung dahinter oder ein aktiver Terminator, was einen zusätzlichen CN/Buchse am Kabel(ende) erfordert.
https://www.tecchannel.de/a/amp/scsi-richtig-eingesetzt,401372
Auch greife ich gern auf (externe) StorEdge UniPacks oder Alternativen zurück, die nativ SCA80 auf 68pol adaptieren. Ggf auch eine Lösung, sofern man extern 50/68-pol Zugang hat. Lässt sich auch unkomplizierter zwischen Systemen hin- und herwechseln/-tragen.
(*) Scheint aber auch Adapter zu geben, die mit integrierter Terminierung daherkommen, wenn man den Angaben Glauben schenkt.
(..) oder ein aktiver Terminator, was einen zusätzlichen CN/Buchse am Kabel(ende) erfordert.
Ergänzung: gibt auch Terminatoren, die man einfach dazwischensteckt. D.h, es gibt eine Buchse zum Laufwerk auf der einen und Stecker für das Kabel auf der anderen Seiten. Solch einen T nutze ich bspw. Hat den Vorteil, man verliert keinen Abnehmer/Buchsenanschluß
Ergänzung: gibt auch Terminatoren, die man einfach dazwischensteckt. D.h, es gibt eine Buchse zum Laufwerk auf der einen und Stecker für das Kabel auf der anderen Seiten. Solch einen T nutze ich bspw. Hat den Vorteil, man verliert keinen Abnehmer/Buchsenanschluß
Interessant. Hast Du bitte mal ein Bild?
Ergänzung: gibt auch Terminatoren, die man einfach dazwischensteckt. D.h, es gibt eine Buchse zum Laufwerk auf der einen und Stecker für das Kabel auf der anderen Seiten. Solch einen T nutze ich bspw. Hat den Vorteil, man verliert keinen Abnehmer/Buchsenanschluß
Terminatoren gehören aber ans Ende des Signals.
Du hast nur den Vorteil, das du den Terminator an den Kabelstecker und an den Gehaeusestecker anstecken kannst, aber nicht dazwischen.
Interessant. Hast Du bitte mal ein Bild?
Dieser Adapter läuft in einem SNI PCD-4G/66, mit AHA-1540CF Ctrl + SCA80 LCD/SE Platte als Teilnehmer problemlos.
Terminatoren gehören aber ans Ende des Signals.
Du hast nur den Vorteil, das du den Terminator an den Kabelstecker und an den Gehaeusestecker anstecken kannst, aber nicht dazwischen.
So kenn ich es i.d.R. auch. Bei dem gezeigten, aktiven Terminator ist das scheinbar anders realisiert. Ich stelle mir das wie eine interne Verlängerung des Kabels vor, wobei der Terminator am "intern verlängerten Ende", innerhalb des Adapters wirkt. Preis um die 10 EUR.
Manchmal auch als "Active-Feed-Through" bzw "aktives Durchschleifen" bezeichnet, wobei nachfolgend als HD68M-HD68F Ausführung.
Allgemeines: Unterschiede zur Terminierung sind bspw nachfolgend nochmal etwas spezifischer in EN beschrieben.
Alles anzeigenSCSI Terminations Information
Show all SCSI Terminations ManufacturersSCSI terminations are electrical circuits placed at each end of a SCSI cable for impedance matching. They are an important part of any small computer system interface (SCSI) that uses hard drives, CD-ROMs, scanners, tape drives, or other SCSI peripherals controlled by a SCSI bus. SCSI terminations are used to close off both ends of the system that begins with the bus. Many different types of SCSI terminations are available. The most common types are passive, active, active negation, high-voltage differential (HVD), low-voltage differential (LVD), multimode (LVD / MSE), forced perfect terminator (FPT), and high- byte terminator (HB).
SCSI terminations consist of both passive and active products. Passive terminations are the simplest, but least reliable SCSI terminations. They use simple resistor networks to terminate the bus in single-ended SCSI-1 short systems with few connected devices. Passive SCSI terminations are driven by the term power-line on the bus, which has equivalent impedance around 132 ohms. Because the typical impedance of most cables is between 85 and 110 ohms, passive SCSI terminations do not provide good impedance matching. Active terminations are used with single-ended SCSI-2 devices and are compatible with passive SCSI terminations. These SCSI terminations consist of resistor networks driven by voltage regulators inside the termination. The voltage regulator generates a termination voltage from the term power and keeps the terminator’s impedance around 110 ohms.
Active negation terminations, high-voltage terminations, and low-voltage terminations are common types of SCSI terminations. Active negation terminations are used with single-ended SCSI buses. They assert a signal that is required to drive the signal voltage low. With active negation SCSI terminations, the signal is de-asserted or driven high, which allows for faster bus speeds. High-voltage differential (HVD) SCSI terminations are used only in differential systems. They consist of a 330/150/330 resistor network. HVD SCSI terminations are not compatible with single-ended or LVD systems or devices. Low- voltage differential (LVD) SCSI terminations are a special, active termination form defined in the SCSI Parallel Interface 2 and SCSI Parallel Interface 3 documents.
Multimode (LVD/MSE) SCSI terminations are used in low-voltage differential (LVD) systems with multimode transceivers. Depending on the voltage level at the DIFFSENSE pin of the cable, the transceiver automatically chooses LVD or multimode single-ended (MSE) when devices power up. Active LVD/MSE terminations respond to the DIFFSENSE line. If the DIFFSENSE voltage is less than 0.7 V, the termination enters single-ended mode. If the voltage is between 0.9 V and 1.9 V, however, the termination enters LVD mode.
SCSI terminations include forced-perfect terminations and high-byte terminations. Forced perfect (FP) SCSI terminations are single-ended devices that use diode clamps to compensate for the mismatch between the SCSI cable and the device connected to the bus. The diode clamps force the termination to the correct voltage; however, this termination is not recognized by the SCSI specifications. High-byte (HB) SCSI terminations use the upper data byte on a wide bus (bits 8 to 15). A high-byte termination is used when the SCSI bus terminates in multiple locations.
Viel Erfolg.
Den "Zwischenterminator" steckt man direkt am letzen Laufwerk dran. Das ist dann völlig OK.